現在切菜機的應用越來越廣了，它代替了傳統的手工操作，很大的提高了工作效率，深受各個企業的喜愛，在使用切菜機的時候，大家是需要按照說明書的要求去操作的，要不然可能就會出現故障問題，今天就給大家具體介紹下切菜機常見故障處理方法是怎樣的。
Now the application of the vegetable cutting machine is more and more extensive. It replaces the traditional manual operation, greatly improves the work efficiency, and is deeply loved by various enterprises. When using the vegetable cutting machine, you need to operate according to the requirements of the manual, otherwise there may be trouble problems. Today, I will introduce to you in detail how to deal with the common faults of the vegetable cutting machine.
1、切削的時間變長。
1. The cutting time becomes longer.
大家在使用切菜機時候，有時會感覺它切削菜的時間變長了，工作效率降低了，這個是怎么回事呢？針對這種情況，大的可能就是刀片已經變得鈍了，沒有之前那么鋒利了，這個是和使用的時間有關系，也會切削的物品的種類有關系，這個處理的方法非常簡單的，那就是對刀具進行修磨就可以了，或者是如果損壞比較嚴重的話，還可以選擇更換刀片。
When using the vegetable cutting machine, people sometimes feel that the cutting time is longer and the work efficiency is reduced. What's the matter? In view of this situation, the most likely thing is that the blade has become blunt and not as sharp as before. This is related to the time of use and the type of objects that will be cut. This treatment method is very simple, that is, grinding the tool, or if the damage is serious, you can choose to replace the blade.
2、切刀的轉向異常。
2. The rotation of the cutter is abnormal.
大家在使用切菜機的時候，發現它的切刀的轉向不正常了，不符合規定的要求了，這個時候可能就是由于電源給接反了原因造成了，大家不妨檢查一下電源的接線情況，看是不是接反了，如果是的話，，就可以對接線進行調整了，在調整過來之后，切菜機的工作就正常了。
When you use the vegetable cutting machine, you find that the rotation of its cutting knife is abnormal and does not meet the specified requirements. At this time, it may be caused by the reverse connection of the power supply. You may wish to check the wiring of the power supply to see if it is connected reversely. If so, you can adjust the wiring. After adjustment, the vegetable cutting machine will work normally.
3、切餡子的時候，轉速變慢了。
3. When cutting stuffing, the speed slows down.
這個情況主要是由于三角帶發生了松動造成的。處理的方法就是對三角帶進行調節，對刀軸一側的皮帶做緊一些，讓皮帶的松緊度保持在合理的范圍內。
This situation is mainly caused by the loosening of the triangle belt. The treatment method is to adjust the V-belt and tighten the belt on one side of the cutter shaft to keep the tightness of the belt within a reasonable range.
大家在使用
大型切菜機的時候，如果出現了上面的這些情況，就可以按照這些方法去處理，一般處理的方法還是比較簡單的，如果發現三角帶松弛的話，就及時的進行糾正，讓它變得緊固起來，這樣才能讓它正常的工作。
When you use a large-scale vegetable cutting machine, if these conditions occur, you can deal with them according to these methods. The general treatment method is relatively simple. If you find that the triangle belt is loose, you should correct it in time to make it tight, so that it can work normally.
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://m.morningvote.com And consult our staff, will serve you wholeheartedly.
